Mounting A Tub
Mounting A Tub
Blog Article
This article following next relating to A Step-by-Step Guide to Installing a Bathtub is indeed enlightening. Check it out for yourself and decide what you think about it.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Installing a bath tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately hard job. If the old bathtub is easily accessible, the job can move immediately; if you need to open up a wall to eliminate the old tub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have actually qualified yourself for the job as well as fit trying it. Rather than employing a service provider to take over a halfway-completed project, it is much better to think about using one prior to you start. Chances are you may need an expert plumber to make tube connections.
This post will certainly aid you install a new tub in your shower room if you have currently acquired a new tub as well as do not need to alter the plan of your previous water pipes.
Your tools as well as product checklist ought to make up the following:
Planning for the Installment
To start with, the sustaining framework supplied with the bath ought to be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop strain on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its last position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome as a result of the restricted accessibility that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will originate from the pipelines. Once the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Using both wood boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the level and changing the feet on the bath tub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Turn on the water system and also inspect all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as additionally inspect the overflow outlet as well as the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub should wait up until the bathtub has actually been utilized a minimum of when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and the other end gives a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in area in between the tap and also the sink. Protect the faucet in position with the supplier supplied backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to permeate the wall surface between the bath as well as the tiling, bring about problems with moisture as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and also fittings. They are sold in tubes as well as cartridges, and also can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the market. It is advisable to fit the tiles using water-resistant or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for taking a few minutes to read our content. Are you aware of somebody else who is sincerely interested in the subject? Feel free to promote it. Thanks a lot for taking the time to read it.
Estimate Free
Report this page